ADIC SNC 5100 Guia do Utilizador Página 213
- Página / 228
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Bootrom Messages 205
6-00020-02
SNC 5100
Startup Message Reference
After the SNC 5100 completes its power-on self-test, it will attempt to find,
load, and run the real-time LIC boot loader.
Bootrom Messages
See the sample code below.
Press any key to stop auto-boot...
0
auto-booting...
boot device : ibmEmac
unit number : 0
processor number : 0
file name : //ffs/vxWorks.st
inet on ethernet (e) : 192.168.1.183
flags (f) : 0x8
target name (tn) : SN600030
startup script (s) : //ffs/sna.rc
Attaching to TFFS... done.
Loading /ffs/vxWorks.st...2697865
Done
Starting at 0x10000...
- User Guide 1
- Copyright Notice 2
- Copyright Notice (Europe) 2
- Safety Notices 9
- Remove AC Power 10
- External Machine Check 10
- Safety Label Check 10
- Fusing Requirements 11
- Product Recycling 11
- Laser Safety 11
- General Restrictions 12
- Usage Restrictions 12
- Regulatory Notices 12
- VCCI Notice (Japan Only) 14
- BSMI Notice 14
- CE Notice 15
- Documentation 16
- Introduction 17
- Configuration Support 18
- Fibre Channel Interfaces 19
- Ultra2 SCSI I/O Interfaces 20
- SCSI Command Support 21
- Ethernet 21
- Service Port 21
- LED Indicators 22
- Supported Platforms 23
- Supported Devices 24
- Operating Specifications 24
- Power Consumption 25
- Power Requirements 25
- 18 Operating Specifications 26
- Install the SNC 5100 27
- Installation Procedure 28
- Installation Procedure 21 29
- 22 Installation Procedure 30
- Host Utility Software 31
- Post-Installation 32
- Other Installation Issues 32
- Wide and Narrow SCSI Buses 33
- (2,3) 40 8 25 8 34
- (3) 80 16 25 16 34
- (5) 160 16 (4) 16 34
- SCSI Bus Termination 35
- Problems on the SCSI Bus 35
- 28 Other Installation Issues 36
- Host Bus Adapter Setup 37
- Installing the SAN Explorer 38
- Other Installation Issues 31 39
- 32 Other Installation Issues 40
- Maintenance Action Plans 41
- Event Codes and Actions 42
- Event Codes and Actions 35 43
- Firmware State = Sync 44
- Event Codes and Actions 37 45
- These event codes are not 48
- Action Reference Table 49
- Start MAP 50
- Visually Inspect LEDs 51
- Check Host Versions 52
- Firmware version 53
- Hardware version 53
- Quick Component Check 54
- Perform Health Check 54
- Database Full MAP 55
- Device Access MAP 56
- Check SCSI Channel Devices 57
- SCSI Channel MAP 58
- Example: 59
- 52 SCSI Channel MAP 60
- Check SCSI Bus Termination 61
- Check for Multiple SCSI IDs 62
- Improper Device Type 63
- Examine SCSI Cables 64
- Examine SCSI Connectors 65
- SCSI Health Check 65
- SCSI Loop Back Test 66
- Testing SCSI Cables 67
- Isolating SCSI devices 67
- Restore SCSI Setup 68
- Fibre Channel MAP 69
- Test GBIC 70
- Examine Cables 71
- Fibre Channel Loop Back Test 71
- 64 Fibre Channel MAP 72
- Replace Fibre Channel Cable 73
- Replace Fibre Channel Device 73
- MAP for the SNC 5100 74
- Temperature MAP 74
- Subsystem 75
- Power MAP 76
- Ethernet MAP 77
- 70 Ethernet MAP 78
- Ethernet MAP 71 79
- 72 Ethernet MAP 80
- IP address> 81
- 74 Ethernet MAP 82
- Service Port MAP 83
- Check the RS-232 Cable 84
- Manager Settings MAP 85
- Verify Host Access to Devices 86
- Removal and Replacement 89
- Procedures 89
- Removing the GBIC 90
- Replacing the GBIC 90
- Removing the SNC 5100 91
- Final Diagnostic Tests 92
- Fibre Channel Tests 93
- Ethernet Test 94
- Updating the SNC 5100 98
- Post-Repair Checklist 99
- SNC 5100 100
- 92 Post-Repair Checklist 100
- 6-00020-02 100
- Post-Repair Checklist 93 101
- 94 Post-Repair Checklist 102
- Service Port Connections 103
- Hardware Required 104
- Verifying the Connection 105
- Updating SNC 5100 Firmware 106
- Saving a Configuration File 107
- Loading a Configuration File 107
- Zmodem Status Code Table 108
- Setting the Time and Date 109
- 102 Setting the Time and Date 110
- Setting the Time and Date 103 111
- Timeserver 112
- Service Port Command 113
- Reference 113
- 106 Commands 114
- Commands 107 115
- 108 Commands 116
- Commands 109 117
- 110 Commands 118
- Commands 111 119
- 112 Commands 120
- Commands 113 121
- 114 Commands 122
- Commands 115 123
- 116 Commands 124
- Commands 117 125
- 118 Commands 126
- Commands 119 127
- 120 Commands 128
- Commands 121 129
- 122 Commands 130
- Commands 123 131
- 124 Commands 132
- command 133
- 126 Commands 134
- Commands 127 135
- Commands 129 137
- 130 Commands 138
- Successful gateAddrSet 139
- Failed gateAddrSet (1) 139
- Failed gateAddrSet (2): 140
- Commands 133 141
- 134 Commands 142
- Commands 135 143
- 136 Commands 144
- Commands 137 145
- 138 Commands 146
- Commands 139 147
- 140 Commands 148
- Commands 141 149
- 142 Commands 150
- SN60023 > 151
- 144 Commands 152
- Commands 145 153
- 146 Commands 154
- 148 Commands 156
- Commands 149 157
- 150 Commands 158
- Commands 151 159
- 152 Commands 160
- Commands 153 161
- 154 Commands 162
- Commands 155 163
- 156 Commands 164
- Commands 157 165
- 158 Commands 166
- Commands 159 167
- 160 Commands 168
- Commands 161 169
- 162 Commands 170
- Commands 163 171
- SN60023 > setNettime 1 172
- Nettime 1 value=0=0x0 172
- Time Host Cronos value=0=0x0 172
- Commands 165 173
- 166 Commands 174
- Commands 167 175
- 168 Commands 176
- Commands 169 177
- 170 Commands 178
- Commands 171 179
- 172 Commands 180
- Commands 173 181
- 174 Commands 182
- Commands 175 183
- 176 Commands 184
- Commands 177 185
- 178 Commands 186
- Commands 179 187
- 180 Commands 188
- Commands 181 189
- 182 Commands 190
- Commands 183 191
- 184 Commands 192
- Commands 185 193
- Kernel: WIND version 2.5 194
- SN600033 > 194
- Diagnostic Command Reference 195
- Special Procedures 196
- Event Log Dump 197
- “/ffs/dump” command 198
- Boot Mode Commands 199
- Diagnostic Commands 199
- Ethernet OK 200
- Diagnostic Commands 193 201
- 194 Diagnostic Commands 202
- Diagnostic Commands 195 203
- 196 Diagnostic Commands 204
- POST Error Codes 205
- Initial POST 206
- Simple Access Test 206
- Bitwalk Test 207
- Memory Size 207
- Pattern Test 207
- Secondary POST 208
- POST Service Menu 209
- Figure 19 NMI 1 210
- Figure 20 NMI 2 210
- Error Displays 211
- 204 POST Service Menu 212
- Startup Message Reference 213
- LIC Initialization Messages 214
- Final Startup Messages 215
- 208 Bootrom Messages 216
- Glossary 217
- RPC Remote Procedure Call 218
- Warranty and EULA 219
Manuais e produtos relacionados com Redes ADIC SNC 5100
Redes ADIC FCR 250 Manual de Serviço
(72 páginas)
(72 páginas)
Redes ADIC FCR200 Especificações
(140 páginas)
(140 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais